Reset ABS Light on Dodge Grand Caravan: Effective Guide

To reset ABS light on Dodge Grand Caravan, you have to follow some simple steps, especially when the module appears to be working just fine, that are shared in this article, along with several techniques you may utilize to reset and turn it off accordingly.

Reset ABS Light on Dodge Grand Caravan: Effective Guide

Therefore, our writers have compiled the subsequent sections to walk you through resetting this warning light while ensuring that any signs of faults in the module aren’t ignored!

How Can You Reset the ABS Light on Dodge Grand Caravan?

You can reset the ABS light on Dodge Grand Caravan by disconnecting the battery, which should wipe the vehicle’s computer memory. You can also check the fuse box for any blown fuse, which you can replace, then check if it resets the light.

Every time you are working on your vehicle, make sure that proper protective clothing is worn, such as thick gloves and clear goggles. Be extra careful with the components of your car as some of these parts are very fragile.

1. Disconnecting the Battery

You can try many methods when looking for a procedure that will allow you to reset the ABS light on your vehicle. They all range in complexity and the time required. One of the most helpful techniques in this situation, especially one that does not require extra tools, is unplugging the car battery.

Doing this essentially wipes out the car’s computer memory, which might be a quick method of resetting the ABS light. Of course, there is no specific guarantee that this procedure always works. Still, there is no harm in trying it out since it is straightforward and does not require any mechanical knowledge to be carried out.

2. Checking the Fuse Box

Suppose you still don’t manage to reset the ABS light on your Dodge Caravan after disconnecting the car battery and reconnecting it. In that case, you can try another technique involving the fuse box. What you need to achieve is to spot the fuse box first of all, and it should usually be found right under the car hood on the side of the battery.

Checking Car Fuse Box

Once you have located it, you must remove its cover and get a test light. In the morning, you can inspect each fuse within the box carefully. To see if the fuses are wrong, you must find the two tiny dots on them and tap them to see whether or not the lamp illuminates.

3. Taking Out Any Blown Fuse

After thoroughly checking the fuse box, you might find a fuse or two that is blown and needs to be fixed. Once you locate any such fuse, you will need to get your hands on the fuse clip and utilize this component to remove the problematic fuse. Having taken it out, you must closely examine it, especially toward its side.

Here, given its unique shape, you should generally see a specific metal wire, which should be easy to identify. This wire will be in the form of the Greek letter, an omega, which also looks identical to a horseshoe symbol.

If this wire is broken, it is the number one indicator that the fuse you are handling is blown. Therefore, it would need to be fixed or replaced immediately.

4. Replacing the Fuse

Now that you have managed to identify the blown fuse, you will then need to replace it. Therefore, to do this, you must know that it can only be replaced with a fuse with the exact specifications. As detailed in the previous sections, it would be ideal to check the remainder of the fuse box to see if you find any more blown fuses.

Replacing Car Fuse

Working with fuses is a much simpler process than many other vehicle components. They don’t tend to go bad quickly. Still, it is crucial always to be prepared, since despite seeming not that importance, they allow the vehicle to operate smoothly.

Therefore, keeping some spare fuses in stock is crucial, never knowing when you might need to replace one. Having spare fuses also saves the driver a lot of time if there are related problems while on the road.

How Can You Reset the Dodge ABS Light Without Any Error Codes?

You can easily reset the Dodge Grand Caravan ABS light without any error codes by turning on the car, then shifting the steering wheel while simultaneously maintaining pressure on the brake. Repeat the process until it works, and you should be ready.

1. Turning on the Car

Suppose you reset the ABS light error that is showing up on the dashboard of your Dodge Grand Caravan. In that case, you might also be troubled by the constant appearance of error codes that are just there without being picked on by diagnostic scanners or other tools.

If that is the instance, you might also be concerned about how the light keeps turning on, even though you have tried other methods to fix it and might have even taken it to a repair shop.

Therefore, to get rid of these phantom error codes that keep showing up, you first need to get inside your vehicle. Then, you have to turn the ignition on, and while you do this, remember to have your foot pressed onto the car’s brake pedal.

2. Shifting the Steering Wheel

Once you are inside the Dodge vehicle, have turned it on, and put your foot down on the brake pedal, you must take hold of the steering wheel. You will need to hold it and promptly turn it towards the right, making sure you go all the way in said direction.

Shifting Car Steering Wheel

Another thing you will need to achieve is grab the shifter and make sure you put it in reverse. Once you do this action, you should be able to quickly drive in reverse, which you will need to do.

3. Adjusting the Shifter

After driving a little in reverse mode, you must put the shifter into drive mode. Once accomplished, you can move the car forward while maintaining a passive speed. While you do this, you will also need to straighten the steering wheel that was turned towards the right-hand side.

4. Releasing the Brake

Since you have repositioned the shifter to “drive” and straightened the steering wheel, ensuring the vehicle moves forward straight before proceeding is essential. To do this action, it is recommended to gradually release the brake pedal while keeping a close eye on the vehicle’s movement.

Once the vehicle moves forward smoothly in a straight line, you can reapply the brake pedal and rerelease it to perform a necessary safety check. This time, as you release the brake pedal, turn the steering wheel gently towards the left to verify that the vehicle’s steering is functioning correctly.

5. Repeating and Checking

After releasing the brake pedal once, you must remove it again. After this, the error codes showing up with the ABS light should disappear. However, they may not go away on the first attempt. If you find that is the situation, try the same procedure again, starting from the top, and at least repeat it a couple of times. Hopefully, you will see the results you desire in no time.

How Can You Know Why the Dodge’s ABS Light Comes On?

You can know why the Dodge’s ABS light comes on by getting a diagnosis from a professional mechanic. It is also possible the brake fluid is the issue. Alternatively, it could also be something with the wheel speed sensor. See a mechanic if you are unable to fix the light’s problem.

  • Low Brake Fluid

While it is ideal to get an actual diagnosis, it might be possible to guess the problem causing this light to appear. Therefore, if you are seeing the ABS error light, there is a chance it is showing up due to an insufficient level of brake fluid in your vehicle. If you didn’t already know, brake fluid is the lifeblood of your car brakes, allowing them to operate without causing issues.

Low Brake Fluid

If the level of brake fluid starts to decrease, it can lead to a decrease in brake performance, which can be dangerous. Suppose the brake fluid level drops to a critically low or runs out altogether. In that instance, you will lose the ability to stop as they become completely unresponsive. As a result, you may start seeing the ABS error lights on your dashboard.

These error lights could be a warning sign to immediately check the brake fluid level and address the issue before it worsens. It’s essential to regularly check your brake fluid level to ensure your brakes are functioning correctly and avoid any potential hazards while driving.

  • Wheel Speed Sensors’ Failure

Apart from the brake fluid being an issue when it comes to the appearance and look of the ABS light, another problem could also lie in the wheel sensor of your Dodge Grand Caravan. If one of these sensors begins to malfunction or fails, it will be picked on by the system as a problem related to the ABS and thus be reported as such.

The reduction, which is right behind the car brakes, might need cleaning in this case as it consists of cog teeth, which are liable to get dirty or damaged over time. If you clean them, it might help the light to disappear. After this, you can test drive the vehicle and see if its performance has improved.

Alternatively, you also have the option of replacing the speed sensor. But it might be very challenging to know which one is problematic. Since it is hard to be sure whether it is the root or main cause of the problem, it might be ideal to get a professional’s opinion before taking further action.

Can Resetting the ABS Light on a Dodge Grand Caravan Also Fix the Airbag Light Issue?

Resetting the ABS light on a Dodge Grand Caravan may not necessarily fix the airbag light issue. These lights indicate separate problems in the vehicle. While resetting the ABS light could potentially resolve issues related to the ABS system, it won’t address the reasons for airbag light on/off. It’s crucial to identify and address the specific underlying cause to ensure the proper functioning of both systems.


While it should usually be easy to turn off the ABS light on your car, sometimes it is more complex than expected, especially if you are unfamiliar with the vehicle’s warning systems. Luckily, we have covered everything you would need to know about the methods to apply when you want to turn it off; some of

the main points in the article are reviewed in the summary here:

  • To reset the ABS light on a Dodge Grand Caravan, disconnect the battery or check the fuse box for any blown fuse that needs to be replaced.
  • If there are phantom error codes, turn on the car, hold the steering wheel, and shift the car to reverse.
  • Then drive forward while straightening the steering wheel, and gradually release the brake pedal while keeping a close watch.
  • To avoid being stranded, keep some spare fuses in stock.

You will now know that the light generally turns on as a warning about something being the matter with your vehicle’s ABS module, but there might be cases where everything seems to be just fine and the warning light is on despite that. Whatever the reason, you can confidently tackle the problem after reading all the different techniques in the post and quickly turn the light off!

5/5 - (14 votes)
Ran When Parked