Throw-Out Bearing Replacement Cost: How Much Will You Spend?

Throw-out bearing replacement cost depends on various factors, including the make or model of the car. The damage to the bearing is often caused by wear and tear.

What Is The Cost Of Throw-out Bearing Replacement

This guide discusses the common signs of a damaged bearing and the cost of replacing the unit.

What Is the Price of a Throw-Out Bearing Replacement?

The price of a throw-out bearing replacement is between $30 and $100, depending on the make and model of the vehicle. Nevertheless, throwout bearings can be purchased at automotive parts’ physical and online stores. The estimate will increase if you hire a professional to install the component.

This is because the mechanic will likely spend a long time (about 4-6 hours) working on the clutch. So, factor labor costs into your budget. Also, be prepared to spend at least $200 for the mechanic’s service.

Furthermore, if the damaged throwout bearing has led to total clutch failure, you must replace the clutch with a new unit. The cost of a new clutch depends on the make and model of the vehicle, but it usually costs between $300 and $800. If there is a need to change the flywheel, a new one will cost between $50 and $200.

What Are the Common Symptoms of a Bad Throw-Out Bearing?

The common symptoms of a bad throw-out bearing on a vehicle are grinding loud noise from the car, difficulty changing gears while driving, and excessive vibration of the clutch pedal. Clutch failure and stiff clutch pedal are other signs of a faulty or damaged bearing.

 

Grinding Loud Noise

The throwout bearing is a vehicle’s transmission or gearbox component that disengages the clutch whenever the pedal is released. It is between the transmission and the engine and operates by pressing against the pressure plate, pushing the clutch disc.

This movement of the pressure plate causes the disc to rotate at a reduced speed than the engine. Thus, it allows the engine to be disconnected from the drivetrain. If the throwout bearing becomes faulty, you will hear a loud grinding or growling noise from the car. You will notice this grinding noise whenever the clutch is engaged or disengaged.

Although the rattling sound from the vehicle indicates that the throwout bearing may be damaged, it could also mean that there are other issues affecting the car. To ascertain the cause of the growling noise, visit an auto repair shop for a proper inspection and diagnosis.

Difficulty in Shifting Gears

Gears are used to change rotational speed and power in a vehicle by transferring the power generated by the engine to the differential. There are many arrangements of gears in a vehicle’s transmission system. Gears are the reason you can increase or decrease the revolution per minute of your car to adjust its speed.

Driver Try To Shift The Gears

Gear shifts are expected to occur smoothly with little to no resistance. If you are experiencing gear shifting issues, this could be a sign that the throwout bearing is faulty. If the bearing starts to fail, it can stop the clutch from engaging or disengaging properly, making shifting the gears difficult.

In some cases, it will be impossible to shift the gears, affecting the vehicle’s movement. If you are unable to shift the gears, it means you cannot use the car until the problem is fixed. Difficulty when changing gears usually arises after you hear a grinding noise from the car.

Excessive Vibration

The clutch pedal is designed to disengage the drive from the engine to the vehicle’s transmission. It can perform different functions such as reducing engine speed, enabling easy changing of gears, allowing the engine to run stationary, and smooth vehicle control.

Ideally, whenever the pedal is pressed, it should move down smoothly. However, if you rest your foot on the pedal and start to feel vibrations coming from it, it means that the bearing has been damaged. The vibrations are an indicator of a damaged bearing. So, once you feel these pulsations on your foot, visit a mechanic to inspect the bearing properly.

Stiff Pedal

The depression of the pedal is responsible for disengaging the clutch. However, if the pedal becomes stiff, it could mean that the throwout’s bearing is faulty. The bearing is designed to have specific lubrication properties that ensure it operates smoothly for a long period. However, wear and tear often cause the bearing to lose its lubrication properties.

Accelerator brake and clutch Pedals Of A Manual Car

The wear out of the lubrication properties means it will become harder or difficult to press down the pedal. At some point, you might be unable to disengage the clutch anymore. Thus, it can be inferred that a stiff pedal is proportional to a worn-out bearing.

Clutch Failure

Sudden or gradual clutch failure can be disastrous for a vehicle and its occupants. Sudden clutch failure is when the component stops working totally, and this will prevent the car from moving. On the other hand, gradual clutch failure doesn’t happen without warning. It is characterized by problems such as the vehicle not stopping when you press the pedal.

Gradual clutch failure is one of the faulty bearing symptoms that occurs when the problem is allowed to persist without repair. If this gradual clutch failure isn’t fixed on time, it can degenerate into sudden clutch failure in the future.

So, it’s best to have your mechanic check the vehicle for a damaged bearing once you notice gradual clutch failure. More so, the clutch failure may be due to another issue. This is the more reason a professional diagnosis is important.

How Long Does a Replacement of the Throw-Out Bearing Replacement Take?

A replacement of the throw-out bearing takes about one to two hours if you have all the necessary tools and components. The duration also depends on whether you have professional expertise. For those not skilled in performing tasks, it might take more time despite following the right DIY replacement process.

The process begins by disconnecting the battery to prevent the engine from starting while working. Then remove the driveshaft to give more room to work. The most time-consuming part of the replacement process is removing the transmission. The transmission has to be removed so that you can access the clutch assembly.

After removing the transmission, it becomes easier to take out the damaged bearing and replace it with a new unit. Before you install the new bearing, clean any debris from the bell housing surface that may cling to the new component. The next step is to reattach the transmission and bleed the clutch system. This bleeding process must happen before you start using the car again.

Once you start the engine, check for leaks. Then take the vehicle on a test drive to evaluate the working condition of the clutch.

As easy as this process might sound, you might face challenges when carrying it out, especially if you have never replaced a bearing. So, you should hire the services of a trusted local mechanic to fix the problem. The mechanic has the skills and experience to fix the problem quickly and correctly.

Can a Faulty Clutch’s Bearing Damage Your Car?

Yes, a faulty clutch’s bearing can damage your car, and the damage can be done in different ways. The damaged bearing can cause the clutch to slip and produce intermittent noise, leading to premature wear of the clutch. If the problem isn’t fixed on time, the clutch may eventually fail.

A Clutch Bearing In Hands Of A Mechanic

Another damage caused by a bad bearing is that the clutch won’t be able to engage the gears properly. If the shifting of the gears becomes difficult, and this difficulty persists, it can lead to premature wear and eventual failure of the transmission components. More so, the debris produced by a failing bearing can get caught in the clutch, causing it to slip and produce a bearing noise.

Furthermore, a faulty bearing will generate pulsations or vibrations on the clutch, and this will deteriorate into damage to the engine mounts. If the engine mounts become defective, it’s only a matter of time before engine damage occurs.

How Long Does the Average Throw-Out Bearing Work?

The average throw-out bearing works for about 50,000 to 100,000 miles. Nevertheless, the exact period that the bearing lasts depends on the car’s make and model. Another important factor that affects the lifespans of the clutch’s bearing is the driving habit of the car owners.

Bad or poor driving habits are one of the causes of a defective clutch’s bearing. If you drive your vehicle hard or do not maintain it properly, it will cause the bearing to be replaced sooner than planned.

You can extend the lifespan of the bearing with proper care and maintenance. You can prolong its life expectancy by regularly checking the clutch fluid level and filling it to the required level when needed. Also, avoid riding the clutch to stop the bearing from experiencing unnecessary stress.

Avoid launching the car from a stop because it puts unnecessary stress on the bearing and can lead to bearing failure. Ensure you visit the auto repair shop regularly to have your vehicle serviced by a mechanic.

When replacing transmission system parts, use OEM (Original Equipment Manufacturer) parts. OEM parts are much preferred to Aftermarket parts because of the quality of standards they are held to.

Frequently Asked Questions

Is an Aftermarket Throw-Out Bearing Better Than Stock?

No, an aftermarket throw-out bearing is not better than stock. Although some available aftermarket bearings claim to be better, this is not factual. Therefore, you shouldn’t replace your damaged bearing with an aftermarket part. It’s best you use an OEM part when changing a defective bearing.

How Long Does a Noisy Clutch Release Bearing Last?

A noisy clutch release bearing can last five minutes or five years, depending on the car owner. It all depends on your attitude toward fixing faults in your vehicle. Once you discover the noises from the clutch’s bearing, you should visit a mechanic to fix the problem.

How Can You Test a Throw-Out Bearing?

You can test a throw-out bearing by taking the vehicle on a test drive. While driving, ensure you listen to a growling noise from the vehicle when you press the pedal. If you hear a noise, that’s your cue that the bearing is faulty.

A Throw Out Bearing On A White Wallpaper

Conclusion

Having read this guide, you now know the replacement cost estimate for a throwout bearing and the symptoms of the problem. Here are our final thoughts on the main points and frequently asked questions discussed in this article:

  • The symptoms of a damaged bearing in a vehicle are loud grinding noise from the car, difficulty shifting gears while driving, and excessive clutch pedal vibrations. A stiff or failed pedal is also a sign of a faulty or damaged clutch’s bearing.
  • The average lifespan of throw-out bearings is about 50,000 to 100,000 miles. Nevertheless, the exact lifespan of the bearing depends on the car’s make and model.
  • The bearing replacement cost depends on the make and model of the vehicle. Thus, it varies for different cars. They often cost between $30 and $100. The bearings can be purchased at automotive parts’ physical and online stores.

With the knowledge gained in this guide, you can easily spot signs of a defective clutch’s bearing and budget for the replacement costs.

Rate this post
Ran When Parked