How To Reset TPMS After New Tires Using Simple Steps

How to reset TPMS after new tires is a very important thing to learn since maintaining adequate tire pressure is critical for your vehicle’s safety and performance. Tire Pressure Monitoring Systems (TPMS) are currently a standard in new automobiles, alerting drivers when tire pressure falls below the prescribed range.

Reset Tpms After New Tires

When you replace your tires, you must reset the TPMS to guarantee proper monitoring. We will lead you through the process of resetting TPMS after installing new tires in this step-by-step guide, allowing you to drive with confidence and peace of mind.

How Do You Reset the TPMS After Installing New Tires?

To reset the TPMS after installing new tires, you have to verify the correct tire pressure, utilize the car’s TPMS reset button, drive at 50 mph, remove and re-connect the car battery, use a TPMS reset tool for your vehicle, and finally inspect for damaged sensors.

1. Understand Direct and Indirect TPMS

Tire Pressure Monitoring Systems (TPMS) are classified into two types: direct and indirect. Understanding the distinction between these two systems is critical when resetting your TPMS after installing new tires. Direct TPMS is based on pressure sensors that are put within each tire. These sensors continually monitor tire pressure and wirelessly relay the data to the vehicle’s onboard computer.

The computer then analyzes the data and notifies the driver if any of the tires’ pressures fall below the recommended level. Direct TPMS gives precise tire pressure measurements in real-time for each tire. Indirect TPMS, on the other hand, does not use pressure sensors within the tires. Instead, it uses the anti-lock braking system (ABS) of the car to monitor wheel speed.

The technology measures each wheel’s rotational speed and finds irregularities that may indicate low tire pressure. Indirect TPMS monitors tire pressure indirectly by measuring variances in wheel rotation, assuming that changes in tire pressure produce a substantial change in rotation speed.

2. Verify the Correct Tire Pressure

After you’ve determined the sort of TPMS your car has, the following step in resetting TPMS after installing new tires is to check the tire pressure. To begin, examine your owner’s handbook or look for a label on the driver’s side door jamb, glove compartment, or inside the fuel door. This data offers the appropriate tire pressure for your vehicle’s make and model.

Measure the pressure in each tire independently with a dependable tire pressure gauge. Remove the valve cover from a tire, push the gauge firmly against the valve stems, and read the pressure shown. Repeat this procedure for all tires, including the spare, if necessary.

Checking Tire Pressure

Compare the measured tire pressures to the suggested values by the manufacturer. If the pressure of any tire falls below the required level, it must be filled. If a tire’s pressure is greater than suggested, it should be progressively reduced until it reaches the proper number.

To inflate the tires, utilize a gas station air compressor or purchase a portable air compressor. Add air in modest amounts, using the gauge to verify the pressure after each addition. This enables exact control while avoiding overinflation.

3. Utilize the Car’s TPMS Reset Button

If your vehicle has a specific TPMS reset button, using it is a simple way to reset the TPMS after installing new tires. This button is often positioned in the driver’s area, however, the exact location varies depending on the car model. To begin, turn off the engine but leave the ignition in the “ON” position.

Look for the TPMS reset button, which is commonly denoted by a symbol that looks like a tire with an exclamation point or the initials “TPMS.” If you can’t find the button, see your vehicle’s owner’s handbook. After locating the TPMS reset button, push and hold it for a few seconds. While holding the button, the tire pressure light on the dashboard may glow, flicker, or flash.

Hold the button down until the TPMS light blinks or stays lighted for a few seconds before shutting off altogether. This shows that the TPMS has been successfully reset. It’s important to note that the length of time you should hold the TPMS reset button varies based on the make and model of your car. For specific directions, consult your vehicle’s owner’s handbook.

4. Drive at 50 Mph

Driving at around 50 mph is a suggested step in resetting the TPMS after installing new tires, particularly for cars equipped with indirect TPMS. This procedure assists the system in recalibration and the establishment of correct tire pressure readings. After you’ve done the preceding procedures and established that the TPMS has been reset, it’s time to take a brief drive in your car.

Driving Car at High Speed

Locate a safe and suitable site, such as a highway or open road, where you can maintain a consistent pace of roughly 50 mph for 10 to 15 minutes. The rotational speed of your tires rises while driving at this pace, and the TPMS sensors detect the changes.

This causes the system to recalibrate and update its readings in accordance with the new tire pressures. Driving at 50 mph allows the TPMS to gather and evaluate sensor data, resulting in precise readings and maximum performance.

5. Remove and Re-Connect the Car Battery

Resetting the TPMS after installing new tires may need disconnecting and reconnecting the car battery in some circumstances. This process serves to renew the system’s electronic components and can aid in TPMS reset success. Make sure the car is switched off and the ignition key is removed before continuing.

Connecting the Car Battery

Find the automobile battery, which is usually located beneath the hood or in the trunk. If you’re not sure where it is, see your owner’s handbook. To remove the battery, first disconnect the negative connector. The negative terminal is often denoted by a “-” sign and is generally black in color.

Loosen the nut that secures the terminal with a wrench or socket, then carefully pull it off the battery post. Avoid touching the positive terminal or allowing it to come into contact with any metal surfaces. Wait a few minutes after disconnecting the negative connector to enable any remaining electrical charge to dissipate.

During this time, the TPMS system can also reset and delete any recorded error codes. Reconnect the negative terminal by inserting it back into the battery post after the waiting period. Using the proper tool, tighten it well.

6. Use a TPMS Reset Tool for Your Vehicle

To begin, obtain a TPMS reset tool that is compatible with the make and model of your car. These tools are available for purchase online or at automotive supply stores. Check that the tool is compatible with your unique TPMS system. To begin, switch off the engine and enter the key into the ignition. Connect the TPMS reset tool to the OBD-II port, which is usually found beneath the dashboard near the steering column.

If you can’t find the port, see your vehicle’s owner’s handbook. Once connected, proceed with the TPMS reset tool’s instructions. The precise methods may vary depending on the tool, but in general, you must travel through the instrument’s menu choices and pick the TPMS reset or relearn function. Begin the reset operation as directed by the tool.

This might include tapping buttons on the gadget, following directions on the screen, or waiting for a set amount of time. Allow the tool to interface with the TPMS system and complete the reset operation while you wait. You may observe the tire pressure light on the dashboard flickering or glowing in a certain pattern during the TPMS light reset.

7. Inspect for Damaged Sensors

After installing new tires, the final step in the TPMS reset procedure is to verify the sensors for signs of damage. The TPMS sensors, which are positioned within each tire, are in charge of monitoring tire pressure and sending data to the TPMS system. Begin by physically evaluating each tire to confirm that the sensors are firmly placed and in good condition.

Damaged Sensors of Car

Examine the sensor housing for any evident evidence of physical deterioration, such as cracks, dents, or rust. Check for loose or missing sensor caps, which protect the sensor from dirt and moisture. If there is any evidence of damage or if the sensors appear to be malfunctioning, a professional technician should evaluate and maybe replace them.

Faulty or broken sensors might cause erroneous TPMS readings or system failure, jeopardizing your safety on the road. After a TPMS reset, the sensors may need to be reprogrammed or re-learned in some circumstances. For precise information on sensor programming or re-learning methods, see your vehicle’s owner’s handbook or a specialist.

Take note of the general condition of the tire during the inspection. Examine the tread for adequate depth, symptoms of uneven wear, and punctures that may require repair or replacement. Keeping the tires in excellent condition aids in precise tire pressure monitoring and optimal performance.

Conclusion

You may reset your TPMS and guarantee correct tire pressure monitoring by following the steps provided in this article on how to reset TPMS after new tires. To sum it up,

the main ideas we’ve discussed are:

  • Learn the distinction between direct and indirect TPMS.
  • Before beginning the reset process, double-check the tire pressure.
  • To reset the system, use the TPMS reset button on your vehicle.
  • Allow the TPMS to adjust by driving at 50 mph for 10-15 minutes.
  • Inspect the TPMS sensors for signs of damage and rectify any faults as soon as possible.

Remember to reference your vehicle’s handbook for detailed instructions and to seek expert assistance if you run into any problems.

Rate this post
Ran When Parked